![]() ![]() Note: "bar height" refers only to the bars and does not include the human readable interpretation (numbers) or drop-down bars (as highlighted in the image below). For Maximum X-dimension (0.0260 inches), the bar height for the UPC-A barcode is 1.8 inches, and the maximum width is 2.936 inches For Minimum X-dimension (0.0104 inches), the bar height for the UPC-A barcode is 0.72 inches, and the minimum width is 1.174 inches The Maximum X-dimension for the UPC-A barcode is 0.0260 inches īased on the X-Dimensions sizes noted, the corresponding height of the barcode will be: The Minimum X-dimension for the UPC-A barcode is 0.0104 inches GS1 General Specifications (GS1 symbol specification tables): The size of your barcode will depend on the size of the bars themselves, which is given by the width of the narrowest black bar (this is called the X -dimension). How big or small can I make my barcode?Ī. Please contact one of the GS1 Standards Professional Barcode Image and Print Vendors to assist you with sizing changes. However, some scanners are limited in what they can read and the choice of an alternate barcode should be researched before being pursued. If you are selling very small or oddly shaped products, other barcodes (besides the UPC-A) are available. While you can change the size of your barcode to best fit your packaging, you should stay within the sizing restrictions noted below. ![]() For this reason, you should NOT resize or crop these barcodes.ĭo you need barcode image file dimensions of other barcodes available in GS1 US Data Hub? View the Barcodes Available article in this Help Center.Ī. barcodes have a fixed relationship between barcode height and width, so if one dimension is modified, the other dimension must be altered by a proportional amount. How much room will the barcode image file take up on my product?Ī: Here are the dimensions of the UPC-A barcode image file that you download in GS1 US Data Hub: Here are questions that members have asked about the UPC-A barcode in GS1 US Data Hub: From the main screen, click Product, then click the "Product Description" link (in blue text). Note: Did you license a single GS1 US GTIN? Then your product is already set to In Use. When this product is ready to share with the marketplace, click Set Status to In Use. When the product is in the PreMarket status, click "View Barcode" for a "For Placement Only" or FPO barcode image. When you assign an available GTIN to the product, and click “Save and Continue,” the product status changes from Draft to PreMarket. *This only applies to IDAutomation barcode fonts designed to print at 12 points on 203 DPI printers such as Code 39, Code 128 or Universal Barcode Fonts.To generate a UPC-A barcode image in GS1 US Data Hub, you must first create the product detail record. Use the following chart to set the X Dimensions that create barcodes of the same width on 203 dpi and higher resolution printers: Printer dots To create the most accurate sizes on printers with different resolutions, set the X dimension (or font point size when using a barcode font) to increments that are a multiple of the size of a dot on the lowest resolution printer. If this were not done, barcodes on the low-resolution printers would not be accurate. In the barcode products, the barcode component will round down the measurement given to the nearest pixel and create the entire barcode from that number of pixels. Therefore, 10 MILS or 0.026 CM should equal 2 dots on a 203 DPI printer. This is because at 203 dpi, the size of each dot in the printer is in increments of 5 mils or. In addition, changing the X dimension when printing to low-resolution thermal printers may not actually have any effect. Because the barcode is created from the X dimension, different sized barcodes are sometimes created on printers with different resolutions. ![]() In the event that a value does not match up exactly with the printer, the component will calculate to the nearest possible X dimension. The NarrowBarWidth (X dimension) in the IDAutomation Barcode Image Generator, Barcode Label Software and Barcode Components can only be adjusted to values the printer can support. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |